dd-wrt setup tab

Your Answer

DD-WRT Repeater Bridge – Set Up as Repeater Bridge
It turned out I simply needed to reboot the main router. Older versions have a slightly different method than newer versions. They will not "interfere" but it does half the available bandwidth. Super User works best with JavaScript enabled. Now would be a good time to enter a NTP server.

Post navigation


If you set wireless security while following the previous post which you should , it may help to reset anyway. This helps narrow down the cause of the problem.

You just squeezed an advanced feature out of a router that it was never designed to have! Thanks for the guide …. I saw another post talking about reducing the wireless key renewal from the default of seconds down to 15 seconds on both the repeater and the main router.

I tried that but there was no change. Is it possible that when you set the static IP, you picked an address that was outside the subnet of the router you were connecting to?

Also, did you give the client bridge the exact same subnet mask as the router you were connecting to? Either of these would prevent the repeater from working properly.

What I eventually had to do was reset the router and start over. In my case, I probably made a simple mistake that I was blind to, and resetting wiped out that mistake. I suspect that you are running into the same kind of problem.

I think that your best bet is to try the same fix I did — reset and start over. You are commenting using your WordPress. You are commenting using your Twitter account. You are commenting using your Facebook account. Notify me of new comments via email. Notify me of new posts via email. This site uses Akismet to reduce spam. Learn how your comment data is processed. Skip to content This is part of a series: Connect wirelessly to another Access Point Wi-Fi router , as if the repeater was any other Wi-Fi capable machine, like a smartphone.

This connection is used exclusively for talking with the AP. Nothing else will connect to this router using the main Wi-Fi connection. Forward packets coming from its wired LAN ports to and from the other router, as if they were connected by wire Pretend to be a second Wi-Fi router Virtual Access Point.

This one is for computers to connect wirelessly to. These steps work on the particular build of dd-wrt that I have: That way, I can avoid any IP address conflicts later. DNS converts a website name into an IP address that a computer can visit. Some pages have more.

Apply them if you want. At this point, you should have a working network. Now from my main router and I can see both the bridge router and the device connected to the bridge router and they all have the same IP address. I can access both routers no matter which one I connect to. BTW, the repeater WiFi signal from the virtual interface is at the same channel as the main router, will this cause interference? Is there a way to put it on another channel?

Plug directly into the second router while configuring it. Put the second router at the end of the first routers sub-net. Now would be a good time to enter a NTP server. Set the Wireless mode to Client Bridge. Set the wireless network mode to what wireless mode you want it to connect to the first. Hit Save, then go to the Wireless Security sub-tab and make sure your pre-shared key is correct. Reboot the router under the administration tab.

Plugged in wired to the router, it will come back up with the. At this point i would recommend that you either setup the connection watchdog, or a timed reboot under the administration tab. By clicking "Post Your Answer", you acknowledge that you have read our updated terms of service , privacy policy and cookie policy , and that your continued use of the website is subject to these policies. Home Questions Tags Users Unanswered. Setup a dd-wrt router as repeater bridge Ask Question.

LWZ 2 7 Set the primary router DHCP range to " Let me know if you run into trouble. Thank you for the detailed reply. But it turned out I simply needed to reboot my main router, for whatever reason I would still enable the scheduled reboot. Disable the things mentioned, you will get better throughput on the second router if you do, as it will free up some ram. If you have found this post at all useful, or think it could be useful to someone else searching.

Consider marking it as answered. LWZ there is no way to change the channel the virtual interface is working on. Both the real SSID and virtual are using the same physical radio. They will not "interfere" but it does half the available bandwidth. Well if I set one radio 2. And I will not suffer from half the bandwidth?


Leave a Reply

In the case in which we are interested, a secondary router running DD-WRT v24 is configured as a Repeater Bridge between a Primary wireless router (of any make/brand/FW) allowing the above configuration. So if the router is set up as a repeater bridge AND it has active clients, the repeater bridge router must talk to two . But for the pièce de résistance, enter the Host WLAN router's web GUI (NAT/QoS->Port Forwarding in DD-WRT) and set up a port forward so you can check on and fully access and control your new repeater outside the WAN (via the Internet). How To Set Up A Repeater Bridge On Your DD-WRT Router To begin, make sure that the main router has a X subnet and leases a DHCP address in the same pool. The secondary router must be running DD-WRT.